The short answer: to paint a room, test for lead if the home is older than 1978, clear and clean the room, patch and sand, prime stains and bare spots, then paint in this order: ceiling, walls, trim. Cut in a 2 to 3 inch band with a brush, roll the wall while it is wet and add a second coat after the recoat time on the can. A 12 by 12 room with 8 foot walls takes about 2 gallons for two coats.
- Paint math: one gallon of finish paint covers about 400 square feet, and a prime coat covers about 300 square feet.
- The order: prep · prime stains and patches · cut in · roll · recoat · clean up.
- Track it: log the paint brand, color and sheen in the Home Maintenance Log ($5.99), or sign up for the weekly HomeBase email.
Our picks for how to paint a room
Printables
Home Maintenance Log
Monthly, seasonal and annual checklists plus a record of every appliance and repair.
Coverage figures are from Utah State University Extension's Selecting Paint guide and the lead-safety advice is from the EPA, both read on November 18, 2026. The page covers supplies, how much paint to buy, prep, priming, cutting in, rolling, the second coat, cleanup and common mistakes.
Paint a room: supplies checklist
| Supply | Why you need it |
|---|---|
| Interior paint, and primer if needed | Two coats of paint, plus primer for stains and bare spots |
| 2 to 2 1/2 inch angled brush | Cutting in along ceilings, corners and trim |
| Roller frame, cover and extension pole | Covering the wall quickly and evenly |
| Paint tray or a 5 gallon bucket and grid | Loading the roller |
| Drop cloths and painter's tape | Protecting floors, trim and fixtures |
| Putty knife, spackle and a sanding sponge | Filling and smoothing holes |
| Cleaner, rags and a step stool | Washing the walls and reaching the ceiling line |
How much paint to buy
Utah State University Extension says a gallon of finish paint covers about 400 square feet on a smooth, sealed surface, and a prime coat covers about 300 square feet. Porous or textured walls take more, so buy a little extra and follow the coverage on the can.
Formula: wall area = 2 x (length + width) x wall height. Subtract about 20 square feet per door and 15 per window, then multiply by the number of coats and divide by 400 (a typical finish-coat figure).
Example, a 12 by 12 foot room with 8 foot walls, one door and two windows:
- Walls: 2 x (12 + 12) x 8 = 384 square feet
- Openings: one door (21) + two windows (about 30) = 51 square feet
- Paintable wall: 384 - 51 = 333 square feet
- Two coats: 333 x 2 = 666 square feet
- Gallons: 666 / 400 = 1.7, so buy 2 gallons
| Room size (8 ft walls) | Wall area | Gallons for 2 coats at 400 sq ft per gallon, before subtracting openings |
|---|---|---|
| 10 x 10 ft | 320 sq ft | 1.6 |
| 10 x 12 ft | 352 sq ft | 1.8 |
| 12 x 12 ft | 384 sq ft | 1.9 |
| 12 x 14 ft | 416 sq ft | 2.1 |
| 14 x 16 ft | 480 sq ft | 2.4 |
Add a quart for touch-ups, and add the ceiling separately at length x width divided by 400 per coat.
Before you start: check for lead
If your home was built before 1978, the old paint may contain lead. The EPA says to contain the work area, keep family members and anyone not working on the project out and avoid dust. Its renovation, repair and painting program page explains the lead-safe work rules for contractors. Its guidance for the do-it-yourselfer is to avoid practices that create heavy dust, such as dry scraping and power sanding without a HEPA vacuum attachment. Test first, and follow the EPA's lead-safe guidance if the test is positive.
Prep: clear, clean, patch and sand
- Clear and protect. Move furniture to the middle of the room and cover it. Lay drop cloths over the floor.
- Turn off the power. Switch off the room's breaker, remove outlet and switch covers and tape over any that stay.
- Wash the walls. Wipe off dirt and grease, rinse and let the walls dry.
- Patch holes. Fill nail holes and cracks with spackle, let it dry and sand it smooth.
- Scuff glossy areas. Lightly sand shiny surfaces so the new paint grips, then wipe off the dust.
- Tape. Press painter's tape along the trim, window frames and baseboards.
Primer: when you need it
| Surface | Prime? |
|---|---|
| New drywall | Yes |
| Patched or spackled spots | Yes, spot prime |
| Stains from water, smoke, ink or grease | Yes, use a stain-blocking primer |
| Dark color to a much lighter one | Usually yes |
| Clean, sound wall of a similar color | Often not needed |
Let primer dry fully before you paint. A paint-and-primer product can still need a separate primer on stains and bare spots.
Cut in, then roll
Paint in this order: ceiling, walls, trim.
- Cut in. With the angled brush, paint a band 2 to 3 inches wide along the ceiling line, in the corners and around trim, doors, windows and outlets.
- Load the roller. Roll it in the tray until it is evenly coated, not dripping.
- Roll the wall. Start a few feet from a corner and roll in overlapping vertical passes. Work back into the wet edge so the brush and roller marks blend.
- Keep the edge wet. Do one wall at a time so the cut-in band does not dry before you roll over it.
- Do not stretch the paint. Spreading a gallon over more area than the label says leaves a thin coat that won't hide.
Second coat
Wait for the recoat time on the can. Cool or humid rooms take longer. Then cut in and roll again. Check each wall in daylight and touch up any thin spots.
Clean up
- Pull the tape while the last coat is still slightly soft so it does not peel the paint.
- Wash brushes and rollers used with latex paint in soap and warm water.
- Seal and label leftover paint for touch-ups, and ask your local waste service how to dispose of extra paint. Don't pour it down the drain.
- Replace outlet covers once the paint is dry.
Painting mistakes to avoid
| Mistake | Fix |
|---|---|
| Skipping prep | Wash, patch and sand first; paint shows every flaw |
| Painting over dust or grease | Clean and let dry |
| Rolling over dry cut-in edges | Cut in a wall at a time and roll while wet |
| Thin, stretched paint | Follow the coverage on the label |
| Recoating too soon | Wait for the recoat time |
| Pulling tape late | Remove it while the last coat is still soft |
More home projects? See our guides to cleaning grout, cleaning baseboards and the home maintenance checklist.
Keep home projects in one place

Write down the paint brand, color name, sheen and room in the Home Maintenance Log ($5.99) so touch-ups match.
Frequently asked questions
What order should you paint a room in? Paint the ceiling first, then the walls, then the trim. Cut in a band along the ceiling, corners and trim with a brush, then roll the wall while that band is still wet so the edges blend. Finish with the second coat after the recoat time on the can.
How much paint do I need for a room? Utah State University Extension says a gallon of finish paint covers about 400 square feet on a smooth, sealed surface. A 12 by 12 room with 8 foot walls has about 384 square feet of wall, so two coats take about 2 gallons before you subtract doors and windows.
Do you need to prime before painting a room? Prime new drywall, patched spots, stains from water, smoke or grease, and very glossy or very different colors. If the wall is clean, sound and a similar color, a quality paint and primer in one usually only needs two coats.
Do you cut in first or roll first? Cut in first, then roll. Brush a 2 to 3 inch band along the ceiling, corners and trim, and roll the wall while the band is still wet, so the brush and roller marks blend.
How long should paint dry between coats? Follow the recoat time on the can. Cool or humid rooms take longer. Rolling over paint that is not dry can pull it off the wall.
How many coats of paint does a room need? Most walls need two coats for even color and coverage. A big change, such as dark to light, may need a primer and two coats, and a similar color change may take one coat plus a touch-up.
What do you do before painting a room built before 1978? Test for lead first, because older paint may contain it and scraping or sanding can release lead dust. The EPA says to contain the work area with plastic, keep children and pets out and avoid dry scraping and power sanding without HEPA controls.
Do you need to sand walls before painting? Sand patched spots until they are smooth and lightly scuff glossy surfaces so new paint can grip. Wipe off the dust before you prime or paint. Avoid dry sanding old paint in a home built before 1978.
What size roller nap should I use? Use a 3/8 inch nap for smooth walls and 1/2 to 3/4 inch for textured walls, as a general rule. Check the paint maker's label for the recommended cover, because it depends on the product.
Should you tape the trim before painting? Taping gives a cleaner edge for a first-time painter. Press the tape down firmly, paint, and pull it off while the last coat is still slightly soft so it does not peel the paint.
How do you clean up after painting? Wash brushes and rollers for latex paint with soap and warm water, seal and label leftover paint for touch-ups and ask your local waste service how to dispose of extra paint. Do not pour paint down the drain.
Can you paint a room in a day? A small room can be done in a day if you start early, prep quickly and use a paint with a short recoat time. Plan the second coat for after the recoat window, and allow extra time for patching and taping.
Newsletter
Get the HomeBase email
Fresh tips three times a week, Mon/Wed/Fri, with our deals and new products, from printables, spreadsheets and bundles to paperback planners and apparel, plus simple home, money and planning tips.
Sources
- US EPA: Lead-Safe Renovations for DIYers epa.gov
- US EPA: Renovation, Repair and Painting Program epa.gov
- Utah State University Extension: Selecting Paint digitalcommons.usu.edu

